Edit Module

Frugal Christmas Gifts Day 22: DIY Liquid Bracelets

Posted: 12/23/11 3:00 PM (Modified: 12/23/11 3:00 PM)

 

So, this morning I posted Day 23 of Frugal Christmas Gifts and now I'm posting Day 22...a bit confused I must say. But still, this contest rocks! Check out this awesome entry into our 25 Days of Frugal Christmas Gifts sponsored by GoldBuyersExpress.com.

{DIY Liquid Bracelets} submitted by Vanessa

I just had to share this awesome craft I found on Pinterest! After some fails and tweaks, I (with the help of the hubs- Ok, he ended up making them all) made these for a Dirty Santa gift exchange. They were a hit! It totally takes me back to my childhood memories of side ponytails, sweatbands and Spandex. Totally.

You'll need:

1 yard of 1/4" Vinyl Tubing & 1/2 yard of 3/8" Vinyl Tubing (Found at Lowes in the Plumbing Department)
Vinyl Adhesive (I purchased LocTite, also found at Lowes)
Glitter or Small Beads of your choice (Make sure the beads are the mini ones)
Water, Cooking Oil and Dish Soap in some form of syringe (I used medicine syringes, given for free by our local Pharmacy)
 

 

 Take your 1/4" tubing and cut of a 6" piece using scissors. If you have a small wrist, you could probably cut it down to 5 1/2", but for a bigger girl like me, I just stuck with the 6" length. You can measure your wrist before cutting and add a 1/4" to the length if you want to as well.

Then, take the 3/8" tubing and cut off a piece about 1/2" long. This will be the connector for the ends of your bracelet. Here's an example of what you should have cut out:

 

 
 
Take your Vinyl Adhesive and glue your 3/8" connector to one side of your 1/4" tube (bracelet part), like so:
 
 
Now that you have that complete, here's the trickiest part of the whole craft:
If you are putting BEADS in your bracelet, you will fill it with COOKING OIL.
If you are putting GLITTER in your bracelet, you will add a drop of DISH SOAP & fill it with WATER
This part is very important because it will help your beads and glitter move around instead of stick to the site of the tube. And when it sticks, it looks gross. 
 
So, to Summarize:
BEADS = COOKING OIL
GLITTER = DISH SOAP & WATER
 
Got it? Ok, Good!
 
If you're making a bead bracelet, put your beads in first, make sure they can move about freely in the tube (they tend to clump together), and stick the syringe of cooking oil on one end and fill the bracelet completely. Like this:
 
 
Once your bracelet is completely full, head over to the sink, remove the syringe, try to remove any air bubbles and connect the bracelet together. Make sure you squeeze the end that does not have the connector glued to it as you insert it, as it will give it suction and help the ends stay together. Take your adhesive and coat the non-glued side of the connector to seal the entire bracelet closed.
 
If you're putting glitter in your bracelet, put just a DROP of dish detergent in the non-connected end of your bracelet. Take about a quarter-sized amount of glitter in your hand and feed it into end of the bracelet with the connector. Wipe off any excess glitter that's found outside of the bracelet.
 
Take your syringe of water and fill the bracelet completely with water, making sure you un-clump the glitter as you go. You can do this by lightly tapping the side of the bracelet. Don't tap it too hard or you'll end up with suds, and you don't really want that! 
 
Once your bracelet is filled, follow the same directions as the bead bracelet to connect the bracelet together and seal.
 
Let your bracelets sit for at least 2 hours so the adhesive can dry and give the bracelets a good seal.
 
 Here's the finished product. Isn't it great?
 
 
This is such a great and inexpensive craft that kids (and kids at heart) will enjoy.
 

I LOVE these!!!  If you like this post, comment below! The post with the most comments will win a diamond valued at nearly $1100 from Gold Buyers Express! Be sure to check out all of our frugal Christmas Gifts!

 

Contest Sponsored By:

 

 

Old to new | New to old
Comments, page 1 of 2 1 2 Next »
Dec 23, 2011 10:25 pm
 Posted by  Anonymous

These are really cute! A blast from the past!

Dec 23, 2011 11:53 pm
 Posted by  SanTaylo

Those look great and fun to make! What happens if you come unglued?

Dec 23, 2011 11:55 pm
 Posted by  Anonymous

Great idea. Very good tutorial.

Dec 24, 2011 01:00 am
 Posted by  Anonymous

I'm sure you can rinse the tubing and start over if it comes apart, but I really don't think it will as long as you use that vinyl adhesive! - Vanessa

Dec 24, 2011 10:24 am
 Posted by  Anonymous

So cute girl!!!! I love this!!!

Dec 24, 2011 10:28 am
 Posted by  Anonymous

Every little girl will love these!!!

Dec 24, 2011 12:29 pm
 Posted by  Marissah74834

This is a really neat craft. I may have to add it to my collection. Thank for the instructions.

Dec 24, 2011 01:25 pm
 Posted by  Anonymous

I love these bracelets!! I'm so going to try this!

Dec 25, 2011 01:00 am
 Posted by  Anonymous

LOVE IT!! Gonna give these a try for sure!

Dec 26, 2011 10:07 pm
 Posted by  Anonymous

Great idea.

Comments, page 1 of 2 1 2 Next »
Add your comment:
Edit Module
Advertisement

Edit Module
Advertisement

Edit Module
Advertisement